How hard is it to replace those? it looks like it might be a pain in the arse. i just swapped the doors and i would like to go ahead and replace the motors they are already slow.
-
94 V6 A4~~LT1 M6~~383 M6 13.1 @ 109 with a 2.1 60' Sold/Stripped
94 Z28 383 A4 Sold
75 Chevy~~~~ SOLD
1992 Convertable RS 305/700r4 <<<Just a Beater
GOT PSi?
Good Cause Your Gonna Need It!!! -
Fred
381ci all-forged stroker - 10.8:1 - CNC LT4 heads/intake - CC solid roller - MoTeC engine management - 8 LS1 coils - 58mm TB - 78# injectors - 300-shot dry nitrous - TH400 - Gear Vendor O/D - Strange 12-bolt - 4.11's - AS&M headers - duals - Corbeau seat - AutoMeter gauges - roll bar - Spohn suspension - QA1 shocks - a few other odds 'n ends. 800HP/800lb-ft at the flywheel, on a 300-shot. 11.5 @ 117MPH straight motor -
cool thanks fred thats gonna be next weekends project94 V6 A4~~LT1 M6~~383 M6 13.1 @ 109 with a 2.1 60' Sold/Stripped
94 Z28 383 A4 Sold
75 Chevy~~~~ SOLD
1992 Convertable RS 305/700r4 <<<Just a Beater
GOT PSi?
Good Cause Your Gonna Need It!!!Comment
-
Its easy and with Shoebox's help even easier. Took me about 45 minutes. Hardest part is drilling out the rivets.Eddie
2000 M6 Trans Am
Tune+exhaust=344WHP
Comment
-
well the hardest part for me is to stop being a bum and just spend the money haha. it wont take but a few minutes so im gonna get the money up and buy two new motors and swap them. i hate pulling my door panel though. getting those dang lock rods back on are a P.I.T.A!!!!!
94 V6 A4~~LT1 M6~~383 M6 13.1 @ 109 with a 2.1 60' Sold/Stripped
94 Z28 383 A4 Sold
75 Chevy~~~~ SOLD
1992 Convertable RS 305/700r4 <<<Just a Beater
GOT PSi?
Good Cause Your Gonna Need It!!!Comment
-
blah be a man and go manual windows, less weigh
i did one on a 02 SS vert and it wasnt too bad, just make sure u got some tape to hold the window up
2009 Honda Civic EX- the daily beater
old toys - 1983 trans am, 1988 trans am, 1986 IROC-Z, 2002 Ram Off-Road, 1984 K10, 1988 Mustang GT, 2006 Silverado 2500HDComment
-
i just took the manual doors off. the car had manual doors and i got tired of it with 5% window tint i couldnt see and it was a pain in the arse too reach over and roll it down so i just switched to power lol94 V6 A4~~LT1 M6~~383 M6 13.1 @ 109 with a 2.1 60' Sold/Stripped
94 Z28 383 A4 Sold
75 Chevy~~~~ SOLD
1992 Convertable RS 305/700r4 <<<Just a Beater
GOT PSi?
Good Cause Your Gonna Need It!!!Comment
-
I know what you are talking about. No kidding I have had my panels off at least 10 times. The trick is you hold the rod with needle nose pliers then press on the lock knob.Originally posted by 1slo_camarowell the hardest part for me is to stop being a bum and just spend the money haha. it wont take but a few minutes so im gonna get the money up and buy two new motors and swap them. i hate pulling my door panel though. getting those dang lock rods back on are a P.I.T.A!!!!! Eddie
2000 M6 Trans Am
Tune+exhaust=344WHP
Comment
-
yea i did the same thing its still a pain in the ARSE!!!! LOL94 V6 A4~~LT1 M6~~383 M6 13.1 @ 109 with a 2.1 60' Sold/Stripped
94 Z28 383 A4 Sold
75 Chevy~~~~ SOLD
1992 Convertable RS 305/700r4 <<<Just a Beater
GOT PSi?
Good Cause Your Gonna Need It!!!Comment
-
No way, If you hold it right it should take about 5 seconds to put on. Takes me about 2 minutes to install the entire panel.Originally posted by 1slo_camaroEddie
2000 M6 Trans Am
Tune+exhaust=344WHP
Comment
-
ooo idk i guess i must jsut be special ed lol jp any news on those pics?94 V6 A4~~LT1 M6~~383 M6 13.1 @ 109 with a 2.1 60' Sold/Stripped
94 Z28 383 A4 Sold
75 Chevy~~~~ SOLD
1992 Convertable RS 305/700r4 <<<Just a Beater
GOT PSi?
Good Cause Your Gonna Need It!!!Comment
Comment